Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterTrusted Door Installation for Boynton Beach Homeowners
A door that binds in the summer humidity, a frame that’s drifted quarter-inch out of square, or a threshold that lets warm air and palmetto bugs wander in - these are the calls we run across Boynton Beach every week. Door installation in Boynton Beach means working against salt air, hurricane code, and houses that have settled into their foundations over twenty or thirty years. TruePane Windows & Doors has served this stretch of the coast since 2008, and Dale Kessler still runs the floor with the same rule he started with: if the pane is not true, the job is not done. That goes for the door slab, the jamb, the hinges, and the sweep. Call (561) 708-6771 and a live person answers, any hour, any day.
What Our Door Installation Service Includes
Entry & Swing Doors
An entry door in Boynton Beach does more than open and close. It has to seal against July’s humidity, stand up to afternoon thunderstorms, and swing true through ten months of heat and two months of near-daily rain. We install entry and swing doors with the frame squared, the reveal set evenly, and the weatherstripping compressed to the manufacturer’s spec, not guesswork. Every install starts with measuring the rough opening twice, because a quarter-inch misread is a door that drags on the tile by August.
Double & French Doors
Double and French doors are where installation craft shows fastest. Two slabs have to meet flush at the astragal, latch without lifting, and stay aligned across the seasonal movement of a slab foundation or a wood-frame wall. We set French doors with equal sight lines, shim the hinges rather than bending them, and adjust the active and passive leaf so the throw bolt lands without a shove. If you’re replacing a pair of swinging or French doors in a 1960s ranch or a newer development off Hypoluxo Road, the difference is in whether the doors still line up three years later.
Bifold & Folding Doors
Bifold and folding door systems live and die by the track. A track that’s even slightly out of level makes the panels bind, jump the rail, or refuse to stack. We install bifold and multi-panel folding doors with the header shimmed level and the track anchored to block, not just screws in drywall. These installations open a living room to a patio or a kitchen to a screen porch, which is exactly the way homeowners in Boynton Beach want to live most of the year, and a sloppy track defeats the entire point.
Pivot Doors
Pivot doors carry their weight on floor and header hardware instead of side hinges, which means the threshold, the pivot point, and the frame have to be dead square. We set pivot doors with the reveal checked at four points and the hardware torqued to the manufacturer’s foot-pound spec. A pivot door that drags near the strike side is usually an out-of-square rough opening, and we correct that with solid shims and blocking, not by tweaking the pivot offset. These doors are heavy, often glass, and worth doing once, correctly.
Storm Doors
A storm door in South Florida is a second line of defense against wind-driven rain and a first line against insects. We install storm doors with the closer adjusted for the actual door weight and swing direction, and we set the expander sweep so it seals against an uneven threshold. The frame gets caulked top and sides, and the drip cap goes on before any trim, because water that gets behind the brickmold is water that rots the jamb two years later. These installations are straightforward, but the difference between airtight and flapping is in the adjustments.
Arched & Custom Doors
Arched and custom doors are where a door stops being a stock item and becomes a millwork project. We’ve installed radius-top entry doors in older Boynton Beach neighborhoods where the arch had to match the existing stucco opening, and we have the shop relationships to order true radius slabs instead of trimming a square door to fit. Custom means the template is verified against the actual opening, not the builder’s plan, and the reveal is scribed to the jamb, not forced with caulk. We take the extra hour to make an arch door swing clean, because the homeowner who orders one notices everything.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Door Installation
We’re an authorized installer for more than a dozen manufacturer lines, and that includes the door brands homeowners in Boynton Beach ask about most. Andersen doors come through our shop often enough that our technicians know the frame joinery and the thermal break details by feel. We register both warranty layers in writing on Andersen installs, and we quote the line side by side on paper against comparable lines so you can see the actual difference, not a sales pitch.
Pella and Marvin doors each have their own hardware, their own weatherstripping profile, and their own tolerance stack. We have installed enough Pella Architect Series and Marvin Ultimate doors to know where a square opening matters most on each. Milgard runs through our van stock for common patio and sliding configurations, which means faster parts and faster fixes when an adjustment is all the door needs. If you have one of these brands in your home now, or you’re comparing them for a replacement, we can give you a real quote with real lead times. Whether you have Andersen, Pella, Marvin, Milgard, or any other make, we can help.
Signs You Need Door Installation Right Now
- You’re lifting the door to close it. A door that rises on the latch side and drops when you let go has hinge wear, a sagging header, or both. In Boynton Beach the humidity swells wood doors in summer, and a door that binds today will be a door that won’t latch by September.
- Daylight shows around the frame. If you can see light past the weatherstripping, you’re air-conditioning the yard. It also means water gets driven in during a summer storm, and water on a door jamb never leaves it alone.
- The threshold has gone soft. A threshold that flexes underfoot or shows rot at the sill is not a repair, it’s a replacement. Soft sills in slab homes near the Intracoastal are a regular find, and the fix starts under the door, not on top of it.
- The door frame has pulled from the wall. A frame that moves when the door latches has lost its anchor to the rough opening. That’s a structural problem, not a shim-and-go situation, and a trained installer needs to reset the frame and fasten it to solid blocking.
- You’re replacing the floor or doing a remodel. The right moment to install a new door is when the doorway is already exposed. We work with remodelers in Boynton Beach to set doors while the framing is open, before drywall and trim hide the problem areas.
Our Door Installation Process - Step by Step
- 1
Measure and inspect the opening. We measure every rough opening twice and check the floor level at the threshold. The first visit also tells us if the jack studs are solid or if water has been working on the corner for years. If the framing is compromised, we say so before any door goes in.
- 2
Write a side-by-side quote on paper. Dale built this company on the practice of quoting manufacturer lines side by side, with warranty durations stated in writing. You’ll see the slab price, the hardware, the installation, and any needed corrections to the opening before you sign anything.
- 3
Prep the opening. We remove the old door, cut out rot, and install or repair blocking at the hinges and strike. The rough opening is rechecked for plumb and square, because a door set in an out-of-square opening will bind no matter how carefully it’s hung.
- 4
Set, shim, and hang the slab. The door is shimmed at every hinge and at the strike, fastened with screws long enough to reach framing, and adjusted until the reveal is even on all four sides. Hardware is torqued to manufacturer spec, and the weatherstripping is tested for compression before we call it set.
- 5
Caulk, trim, and test. We caulk behind the brickmold, set the drip cap, install or reset the threshold, and run the door through twenty cycles. Then we register both warranty layers in writing, in front of you, before the truck leaves the driveway. That’s The Keystone Standard.
How Much Does Door Installation Cost in Boynton Beach?
What moves the number is the opening, not just the door. A bad jamb, a rotted sill, a floor that has settled a half inch on one side, all of it adds labor that comes into the price honestly. We quote fixed, itemized numbers and we don’t write change orders for surprises we could have seen on the first visit. The free estimate includes checking the rough opening, the floor, the existing trim, and the hinge-side framing, because a square deal starts with a square look at what’s behind the wall. Call (561) 708-6771 and we’ll put the number on paper before you decide anything.
Door Installation Near Boynton Beach - Our Service Area
We install doors throughout Boynton Beach and the surrounding communities, from the older ranch streets off Federal Highway to the newer builds west of I-95, and we run the same trucks down to Door Installation in South Palm Beach and over to Door Installation in Golf. Homeowners in Lantana, Manalapan, Ocean Ridge, Gulf Stream, Atlantis, Delray Beach, Lake Worth Beach, Greenacres, and Palm Springs call the same local number and get the same crew of background-checked, uniformed installers. We don’t route calls to a regional office, and we don’t treat an Ocean Ridge front door as any less important than a Boynton Beach one. The Done Right Promise applies everywhere we work, and both warranty layers get registered in writing on every job, in every city.
Serving Boynton Beach, FL - Our Local Coverage Area
We’re based in the Boynton Beach area and know this community well, offering everything from Entry & Swing Doors to custom solutions. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Door Installation in Boynton Beach
What is door installation?
Door installation is the process of setting a new or replacement door, its frame, its hinges, its hardware, and its weatherstripping into a rough opening so the slab swings true and seals tight. It includes measuring the opening, correcting any framing problems, shimming the jamb, and adjusting the sweep and threshold. In Boynton Beach, door installation also means working to Florida building codes for wind and water, especially on exterior doors and impact-rated openings.
How long does door installation take?
A standard single entry door, with the old door removed and the opening in decent shape, usually takes four to six hours from arrival to final caulk and test. Pre-hung doors with rot repair can run a full day, and double French doors or pivot doors often take two visits if trim or paint needs to set before final adjustment. We’ll give you a time estimate on the quote, and we’ll be there when we say.
How much does door installation cost in Boynton Beach?
Most door installations in Boynton Beach run between $450 and $1,800 in labor, with complete entry door packages from $1,400 to $3,400 depending on the slab, hardware, and condition of the opening. French doors, pivot doors, and custom work run higher because they have more working parts and tighter tolerances. Our quotes are itemized and fixed, and a free estimate at (561) 708-6771 tells you the exact number for your house before you spend a dime.
Do you service Andersen, Pella, Marvin, or Milgard doors?
Yes. We are an authorized installer for more than a dozen manufacturer lines, and that includes doors. Our technicians work with these brands regularly and know the frame joinery, weatherstripping, and hardware tolerance of each line. We can also service and replace doors from manufacturers not on that list, and we quote brands side by side on paper so you can see the real difference.
Is door installation available for emergencies?
A door that won’t close, a frame that’s been kicked in, or a broken door after a storm needs to be handled right away. A live person answers the phone at (561) 708-6771 around the clock, every day of the year. We will send a technician when you need one, and we’ll secure the opening and assess the full install or repair on the spot.
What warranty covers a new door installation?
Every door installation with TruePane carries The Keystone Standard: both manufacturer warranty layers registered in writing, with the durations stated, before the truck leaves the driveway. Our workmanship is also covered by the Done Right Promise. If it is not done right, we make it right, with no paperwork fights and no fine print. You’ll see the warranty terms in writing on your quote.
How should I prepare for a door installation visit?
Clear the area inside and outside the doorway, move anything within about six feet of the door, and make sure the technician has a clear path from the truck to the opening. If you have pets, plan for them to be in another room while the door is open for removal and install. We handle the old door removal and haul-away, we protect the floor at the threshold, and we leave the work area swept. Call (561) 708-6771 for an exact quote, estimates are free.
Schedule Your Door Installation Service in Boynton Beach Today
If your door binds, sags, or lets water in, call (561) 708-6771. A live person answers, any hour, any day, and a free estimate puts the real number in writing before you decide anything. TruePane Windows & Doors has served Boynton Beach since 2008, and Dale Kessler’s rule hasn’t changed: if the pane is not true, the job is not done. You can reach us through our home page, or call for your free estimate today.
Written by Dale Kessler, Owner at TruePane Windows & Doors, serving Boynton Beach since 2008.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.