Therma-Tru Custom & Geometric Windows Nationwide | TruePane Windows & Doors

Therma-Tru Custom & Geometric Windows in Boynton Beach: What to Know First

We install and service Therma-Tru custom and geometric windows throughout Boynton Beach, from arched transoms over entry doors to oversized trapezoids and radius units. Most replacement work runs a two-to-four week lead from measure to install, and you’ll get a written, line-item price before any work begins, not a ballpark. If you’re calling about a Therma-Tru window that’s fogged, hard to operate, or leaking around a shaped frame, we’re the independent crew that’ll sort it out. Call (561) 708-6771 and a live person answers, day or night.

Call (561) 708-6771

This page is for Boynton Beach homeowners who own Therma-Tru windows, specifically the custom shapes and geometric units, and want straight answers on repair, replacement cost, and what actually holds up in our coastal climate. Dale Kessler grew up off Lawrence Road in the Meadows section, so we know exactly what salt air and summer storms do to a window that was never quite set right.

How Therma-Tru Products Fail - and How We Fix Them

• Seal failure on radius and arched units. Therma-Tru’s custom bent-glass units, especially the ones with true divided lites, run a higher risk of desiccant saturation than their standard rectangular lines. The curved spacer bar flexes more during temperature swings, and in Boynton Beach where we swing from 90-degree afternoons to 70-degree AC interiors, that flex eventually cracks the seal. We see it most on the Smooth-Star and Classic-Craft lines where homeowners report “fog between the panes” around hurricane season. The fix is a full IGU replacement with a fresh spacer system, not a drill-and-fill patch, because the patch buys you eighteen months at best.
• Sash sag on oversized geometric openings. A trapezoid or half-round window wider than five feet carries a lot of glass weight on hinges that weren’t spec’d for it. Therma-Tru’s factory hardware is adequate for standard sizes, but on oversize custom units we regularly replace the factory balance system with a heavier-rated aftermarket set from Caldwell or Truth. The symptom is a sash that binds at the top corner in July and swings free in January. That’s a geometry problem, not a brand problem, and the right hardware fixes it permanently.
• Frame sealant breakdown at the mull joints. On multi-panel geometric assemblies with mulled fixed units, the factory-applied sealant between mulls dries out in about seven to ten years under Florida UV exposure. We’re pulling apart Therma-Tru assemblies in Boynton Beach neighborhoods like Quantum Lakes and Hunters Run where water is getting in at the joint, not the glass. We re-glaze the mull with a marine-grade sealant rated for our humidity, then re-shim the entire assembly so the mull isn’t carrying load it wasn’t designed for.
• Cladding pitting on coastal-facing elevations. Homes east of Federal Highway or along the Intracoastal get salt spray that pits the extruded aluminum cladding on Therma-Tru’s custom shapes faster than the manufacturer’s inland test data suggests. The telltale is white oxidation blooms at the bottom corners of a radius unit that faces the water. We’re not going to tell you to replace the whole window for that. We strip, treat, and refinish the cladding where the substrate is sound, or replace the clad segments on units where corrosion has compromised the frame.
• Failed glazing tape on fixed picture units. Therma-Tru uses a two-sided glazing tape on some fixed custom shapes, and that tape has a service life. When it goes, the glass starts to rattle inside the frame on windy days, usually the northeast corner first. We hear this all the time from homeowners in Chapel Hill and Boynton Lakes. The fix is pulling the stop, cleaning the old tape, re-bedding the glass with a butyl-based tape rated for coastal wind loads, and re-securing the stops. It’s a same-day job on most fixed units.

Our Therma-Tru Custom & Geometric Windows Process

1. 1
   Measure and document. We measure every opening twice, including the diagonal cross-checks on shaped units. You don’t guess at a radius opening and get it right by accident. Dale’s rule from his father’s finish carpentry days applies: the rough opening tells you the truth, so listen to it first.
2. 2
   Diagnose the root cause. Is the glass failed, the frame racked, the hardware undersized, or the opening itself out of square? We tell you what’s actually wrong, not what’s convenient. If it’s a sash that needs new balances, we don’t sell you a new window.
3. 3
   Parts decision, in writing. We lay out OEM Therma-Tru parts side by side with quality aftermarket equivalents where they make sense. You see both prices, both warranties, and we note which one makes sense for your application. If OEM is required to keep a manufacturer warranty intact, we say so plainly. If the aftermarket part outlasts OEM in our climate, we tell you that too.
4. 4
   Set, shim, and seal. We install or repair with the frame shimmed true, plumb, and square. Not close enough. True. That’s the name on the truck and the rule on the whiteboard: if the pane is not true, the job is not done.
5. 5
   Test and register. We run the unit through full operation, check the seal lines under light, and verify drainage paths. Then we register both manufacturer warranty layers in writing before the truck leaves the driveway. Durations stated, no fine print to dig through later.
6. 6
   Walk the job with you. You see the finished work, ask your questions, and get a straight answer. The Done Right Promise means if something’s not right, we make it right. No paperwork fights, no arguing.

What Therma-Tru Custom & Geometric Windows Costs in Boynton Beach

Straight numbers, because you deserve them before you pick up the phone. A single arched or radius Therma-Tru replacement unit typically runs $850 to $2,400 installed, depending on size and whether it’s fixed or operable. An oversized trapezoid or pentagon runs $1,600 to $3,800. A full geometric window package on a Boynton Beach gable or feature wall starts around $4,500 and goes up from there based on glass package, impact rating, and hardware. Seal repair on a single IGU with curved glass runs $400 to $900; hardware replacement on a sagging sash runs $250 to $700 per unit. What moves the price: size of the rough opening, whether the old frame gets reused or replaced, impact-rated vs. non-impact glass, and whether we’re correcting someone else’s out-of-square install. Call (561) 708-6771 and we’ll come measure and give you a written quote. No surprises on the bill, ever.

Why Boynton Beach Homeowners Call TruePane Windows & Doors for Therma-Tru Work

We’re an independent Therma-Tru service provider, not a franchise, and we’ve been at this since 2008. That matters because a Therma-Tru geometric window with a failed radius seal needs someone who’s seen it before and knows the fix without guessing. Our techs are background-checked and uniformed, and they work in your home the way they’d work in their own mother’s. Every job carries the Done Right Promise backed by The Keystone Standard: both manufacturer warranty layers registered in writing, durations stated, before the truck leaves your driveway. And we don’t pretend every window should be Therma-Tru. If PGT, CGI, CWS, or ES Windows is the better fit for your opening, we’ll quote those side by side on paper. We’ve been in Boynton Beach long enough to know that the right answer for a north-facing interior wall isn’t the same as the right answer for an east-facing coastal elevation. Live person answers the phone 24/7. If it’s not in writing, it’s not a guarantee, it’s a conversation.

FAQs