Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterMr-Glass Roof Replacement & Installation in Boynton Beach: What to Know First
Mr-Glass roof replacement and installation in Boynton Beach is work we handle regularly as an independent Mr-Glass service provider. Most skylight and roof-glass replacements run one to three days depending on framing condition, and pricing typically starts around $1,200 for a straightforward curb-mounted skylight swap and climbs from there when decking, flashing, or curb work enters the picture. We quote on paper, line by line, so you know exactly what the number covers before any work is scheduled.
This page is for Boynton Beach homeowners who have Mr-Glass skylights, roof windows, or glass roof panels that have failed, leaked, or fogged, and who want the replacement done once. If that sounds like your situation, call us at (561) 708-6771. We’ll walk through what you’re seeing and whether it warrants a repair or a full replacement, with no charge for the conversation.
How Mr-Glass Products Fail - and How We Fix Them
Mr-Glass roof glass has its own failure patterns, and after years of working on these units across Boynton Beach, we’ve learned what to look for before we touch a single fastener. Here’s what we see most often:
- Seal failure on Mr-Glass thermopane roof units. The insulated glass in Mr-Glass roof assemblies can lose its edge seal, and in Boynton Beach it tends to show up right around hurricane season when humidity spikes. You’ll see condensation between the panes that won’t wipe away from either side. The fix is a full replacement glazing unit, not a patch. We measure the existing frame, order an exact-fit insulated unit, and re-set the glass with fresh glazing and new setting blocks.
- Flashing failures where the Mr-Glass curb meets the roof deck. We replace more Mr-Glass units because of water getting in around the curb than because of the glass itself. South Florida sun breaks down flashing sealant faster than manufacturers expect, and after ten or twelve years, the corner laps are a common leak point. On a replacement, we don’t reuse old flashing. We cut back the shingle or tile, install new step flashing and curb cap flashing, and re-bed everything with a sealant rated for our UV load.
- Frame corrosion on older Mr-Glass aluminum roof windows. Mr-Glass used aluminum frames on many of its earlier roof windows, and salt air from the Intracoastal accelerates pitting and rust at the corners. If the frame shows structural corrosion, not just cosmetic staining, the right move is a full unit replacement. We’ll tell you straight if the frame is salvageable. We won’t put new glass in a frame that’s going to fail again in three years.
- Cracked or spalled glass from storm debris and hail. When a Mr-Glass roof panel takes a direct hit from a palm frond or hailstone, the glass can crack or develop shallow surface chips called spalls. On a roof unit, even a small crack is a structural issue because the panel carries wind load every time a front moves through. We replace the panel with tempered or laminated safety glass that meets current Florida building code for overhead applications, which older Mr-Glass units sometimes predate.
- Hardware and operating-mechanism wear on venting Mr-Glass roof windows. Mr-Glass venting skylights use a crank or motor to open and close. After years of exposure, the arms, hinges, and sensors wear out, and the window either won’t hold open or won’t seal tight when closed. When the glazing is still sound, we can replace the operating hardware with current OEM or equivalent parts. When the glazing is also shot, a full replacement is usually cheaper than fixing both halves of the problem separately.
Our Mr-Glass Roof Replacement & Installation Process
We don’t send a salesperson out to size up the job. We send a glazier who actually installs roof glass. The process is straightforward, and nothing happens until you approve the number in writing.
- 1
Site inspection and roof access. We look at the Mr-Glass unit from inside and out, check the curb condition, roof decking around the curb, and the glazing state. We shoot rough opening dimensions with a laser measure, because the glass size and the frame size are two different numbers and cutting corners on that is how leaks get born.
- 2
Written quote with line-item pricing. You get a paper quote that separates materials, labor, disposal, and any decking or flashing repair. If a cheaper aftermarket part is a sound option for your Mr-Glass unit, we’ll tell you. If we think OEM is the only choice that will hold up, we’ll tell you that too. You decide with the facts in front of you.
- 3
Parts and glazing order. We order the Mr-Glass replacement glazing or full replacement unit to the precise measurements. For custom roof panels, this step usually takes one to three weeks depending on the manufacturer. We don’t cut corners here, and we don’t board up your roof for a month. You stay informed on timing.
- 4
Removal and re-set. We pull the old unit, inspect the curb and decking, make any necessary repairs, and install the new unit with new flashing, new fasteners, and new sealant. Everything goes in per the manufacturer’s installation spec, so your Mr-Glass warranty stays intact, and per Florida code for roof penetrations.
- 5
Water test and cleanup. Before we call the job done, we run water over the curb and flashing to confirm the seal. Then we clean the glass interior and exterior, and haul away every piece of old material. The only evidence we were there should be the new unit looking like it belongs.
- 6
Paperwork and warranty registration. This is The Keystone Standard. Both manufacturer warranty layers get registered in writing before our truck leaves your driveway, with the durations stated plainly. You walk away with hard copy, not a vague promise.
What Mr-Glass Roof Replacement & Installation Costs in Boynton Beach
What you pay depends on the unit type, size, access difficulty, and what we find when the old unit comes out. Here’s a straight look at typical ranges we see on Mr-Glass work in Boynton Beach:
- Fixed skylight replacement (curb-mounted, up to 2×4 feet): $1,200 to $2,400 installed with new flashing
- Venting Mr-Glass roof window replacement: $1,800 to $3,600 for motorized or manual units, depending on size and mechanism
- Insulated glass replacement only (frame reused): $700 to $1,500 per unit, assuming the frame and flashing are sound
- Full curb rebuild with decking repair: adds $400 to $900 depending on how much rotten wood is found around the curb
- Custom glass roof panel replacement: $2,500 and up; project-priced after measurement and structural review
What moves the number: roof pitch and access (a steep tile roof costs more to work on safely than a flat membrane roof), whether the curb needs rebuilding, whether we’re dealing with a second-story lift, and whether the warranty requires OEM glazing. The fixed price on your written quote is the price you pay. No change orders, no surprise line items. Call (561) 708-6771 for a free estimate on your Mr-Glass roof unit, and we’ll give you a number you can actually plan around.
Why Boynton Beach Homeowners Call TruePane Windows & Doors for Mr-Glass Work
We’ve been at this since 2008 in this community, and we approach a Mr-Glass roof replacement the way we approach every window and door we install: if it’s not in writing, it’s not a guarantee, it’s a conversation. Our Done Right Promise means that if the job isn’t right, we come back and make it right. No paperwork fights. No fine print. The Keystone Standard goes with every job, and both warranty layers on your Mr-Glass replacement are registered before we leave your driveway.
Our technicians are background-checked, uniformed, and trained on Mr-Glass units as well as PGT, CGI, CWS, and ES Windows products. That matters because if a replacement strategy calls for a different glazing spec than what Mr-Glass originally shipped, we know what crosses over and what does not. A live person answers the phone 24/7 because when a roof unit cracks open ahead of a summer storm, you don’t want to leave a message. And if a Mr-Glass repair doesn’t make economic sense, we’ll say so plainly and quote you a replacement option from another line without any gamesmanship. The goal is a roof that holds water out for decades, not a transaction.
FAQs
It depends on what has failed. On a Mr-Glass roof unit in Boynton Beach, a failed insulated glass seal typically means replacing the glazing unit, not repairing it, because the argon or air between the panes has escaped and cannot be restored. Worn operating hardware on a venting unit can often be replaced without touching the glazing. We’ll inspect and tell you which path makes sense. Call (561) 708-6771 for an honest assessment, and the estimate is free.
No, if the work is done correctly. As an independent Mr-Glass service provider, we use OEM glazing and replacement parts where the warranty requires them, and we follow manufacturer installation specifications. Both warranty layers get registered in writing through The Keystone Standard, so there’s no argument later about what’s covered or for how long. If you’re unsure where your Mr-Glass warranty stands, call us and we’ll help you sort it out.
For a typical curb-mounted Mr-Glass skylight in Boynton Beach, the on-site work takes one day, assuming the curb and decking are sound. Custom glass roof panels and jobs that uncover rotten decking take longer, usually two to three days on site. The biggest variable is glazing lead time, which runs one to three weeks for custom units. We’ll give you a straight timeline on the written quote, and we don’t leave a roof opening exposed while parts are in transit.
Look for water marks on the ceiling or wall near the unit. If the staining traces to the corners or edges of the opening, the flashing at the curb is the most likely source. Condensation trapped inside the glass means a seal failure, not a leak from the roof. In Boynton Beach, where we get both intense UV and torrential afternoon storms, flashing failures on Mr-Glass units are more common than glass failures. We’ll diagnose which one you have before quoting any work, and the diagnosis call is free.
Yes, we install and replace Mr-Glass units on flat and low-slope membrane roofs, which are common in parts of Boynton Beach. The curb detail and flashing method differ from a pitched shingle roof, and the sealant and underlayment have to be rated for standing water exposure after a heavy downpour. We’ve been handling our local flat-roof conditions for decades, and we’ll spec the right materials for your roof type. Call (561) 708-6771 to schedule a site visit.
If you have a Mr-Glass roof unit in Boynton Beach that’s fogged, cracked, leaking, or just not what it used to be, call (561) 708-6771. We’ll take a look, give you a written number, and if it makes sense, replace it right. Done right is the standard, and we stand behind it.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Boynton Beach and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.