Mr-Glass Impact Windows Nationwide | TruePane Windows & Doors

Mr-Glass Impact Windows in Boynton Beach: What to Know First

We install, replace, and repair Mr-Glass impact windows throughout Boynton Beach, and most jobs are completed in a single visit. A typical Mr-Glass impact window replacement in this market runs $900 to $2,400 per opening, depending on the line, size, and whether the frame needs full replacement or a sash-only swap. We’re an independent Mr-Glass service provider, not a factory dealer, which means we quote side by side across manufacturer lines so you can see exactly what your money buys. If you own a Mr-Glass window that’s fogged, binding, or leaking after a storm, call (561) 708-6771 and talk to a live person, any hour, any day.

Call (561) 708-6771

This page is written for the homeowner in Boynton Beach who’s had Mr-Glass windows in the house for years and wants straight answers about what’s failing, what it costs, and whether repairing beats replacing. You’ll find series-specific detail below that you won’t get from a manufacturer brochure.

How Mr-Glass Products Fail - and How We Fix Them

Mr-Glass has put several impact-rated lines into Boynton Beach homes over the years, and we see the same failure patterns repeat themselves block after block. Here’s what actually goes wrong, and what we do about it.

• Mr-Glass 800 Series casement cranks and operators. The 800 Series is common in older Boynton Beach ranch homes built through the 1990s. The operator gears strip long before the glass or the frame gives out, especially on the east-facing walls where salt air works into the mechanism. The window gets stiff, then binds, and finally the crank spins without moving the sash. We replace the operator assembly with OEM or a quality aftermarket equivalent, re-shim the sash so it tracks square, and lubricate with a dry film that won’t collect Boynton Beach’s persistent sand and salt.
• Mr-Glass single-hung impact units with blown seals. We see fogged Mr-Glass single-hungs most often in the Leisureville and Chapel Hill neighborhoods, and it’s almost never the glass itself. The desiccant strip inside the insulated glass unit saturates after years of Boynton Beach humidity cycling, and once it’s spent, condensation gets trapped between the panes permanently. The fix is an IGU replacement, not a window replacement. Our standard recommendation: if the frame is square and the balance system still works, replace the glass unit and save upwards of 60 percent versus a full window swap. Dale Kessler will tell you a failed seal always shows up right around hurricane season, never in March, because that’s when the pressure difference is biggest.
• Mr-Glass 850 Series horizontal sliders that jump the track. The 850 slider uses a nylon roller that wears flat on one side after fifteen-plus years of opening and closing. When the roller flattens, the sash drops a quarter inch and starts dragging on the aluminum track pad, and eventually it skips out of the guide entirely. We replace both rollers, not just the bad one. Replacing one is a temporary patch; replacing both means the window operates correctly for another decade. The original rollers are often discontinued, so we machine-match the aftermarket equivalent to the factory spec before ordering.
• Mr-Glass impact picture windows with failed perimeter glazing seals. This failure runs hard in Boynton Beach houses built before 2005. The perimeter sealant between the impact glass and the aluminum frame cures to a brittle hardness after years of direct sun and hurricane heat-soak, and hairline cracks let water in behind the glazing bead. What the owner notices is weep holes that leave calcium trails down the stucco, plus a dull rattle when heavy wind loads hit the glass. We pull the bead, clean the glazing pocket, and re-bed the unit with a structural silicone rated for impact-rated glass installations, never an off-the-shelf caulk.
• Mr-Glass 900 Series picture and transom combinations with frame racking. The 900 Series is visually attractive, a wide picture unit with a transom above, and it was marketed mostly in the newer subdivisions west of Jog Road. The weak point isn’t the glass; it’s the mullion joint between the picture unit and the transom. When the rough opening wasn’t shimmed perfectly, the header load transfers to that joint, and over time the seam opens enough to tell you something’s wrong with how the two units meet. The fix is often to pull the mullion cover, re-shim the header, re-secure the mullion anchors, and reset the glass. That’s the kind of job where we measure the opening twice because if the framing isn’t true, the new window never will be.

Our Mr-Glass Impact Windows Process

Every Mr-Glass job we do in Boynton Beach follows the same sequence, and we don’t skip steps when the driveway is hot and the day is running long. Here’s what a typical call turns into.

1. 1
   Phone diagnosis. A live person answers, 24/7. We ask the questions that tell us whether it’s a glass issue, a frame issue, a hardware issue, or a flashing issue before we ever send a truck.
2. 2
   On-site measurement and inspection. Our technician measures every opening twice, inspects the existing Mr-Glass frame for square, plumb, and water intrusion, and documents it in writing. If the rough opening is out of true, we tell you then, not after the new unit is being set.
3. 3
   Parts decision on paper. We quote OEM Mr-Glass components side by side with quality aftermarket equivalents where one exists, with prices written down. If OEM is backordered, we tell you the real lead time. No promises we can’t keep.
4. 4
   The repair or replacement. We remove the old unit or failed component, prep the opening, install the replacement, and clean up after ourselves. Most Mr-Glass impact window jobs are done in one visit.
5. 5
   Storm test and warranty registration. We run water and air checks on the install before we leave, then register both manufacturer warranty layers in writing, with durations stated. The Keystone Standard is what we call it, and it’s not a handshake.
6. 6
   Your Done Right Promise starts. If anything about our workmanship isn’t right within 90 days, we fix it. No paperwork fight, no arguing, no fine print that covers neither.

What Mr-Glass Impact Windows Costs in Boynton Beach

Here’s the straight answer. These are the ranges we quote in Boynton Beach, and they stay put once written down: we don’t do change orders on a Mr-Glass repair unless we find hidden structural damage, and if we do, we stop and show you before spending another dollar.

Price moves on three things: the exact Mr-Glass series you have, the size of the unit, and whether the original frame is worth saving. We’ll walk you through all three when we quote. Call (561) 708-6771 for a free estimate on your specific Mr-Glass situation.

Why Boynton Beach Homeowners Call TruePane Windows & Doors for Mr-Glass Work

We’re a local Boynton Beach company, not a franchise playbook, and we’ve been serving Palm Beach County communities since 2008. Dale Kessler founded TruePane in 2008 on a rule his father, a finish carpenter, would recognize: if the pane is not true, the job is not done. Our technicians are background-checked, uniformed, and trained to treat your home the way they’d treat their own mother’s. We quote PGT, CGI, CWS, and ES Windows alongside Mr-Glass on paper so you understand the comparison, and if your Mr-Glass unit is beyond saving, we’ll tell you which of those lines is the honest replacement for your opening. Every install carries the Done Right Promise. If it’s not in writing, it’s not a guarantee, it’s a conversation.

Frequently Asked Questions