Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterTrusted Custom & Geometric Windows for Boynton Beach Homeowners
Custom and geometric windows in Boynton Beach replace the square-hole limitation with glass cut to an architect’s line: circles, hexagons, eyebrow arches, trapezoids, and oversized rectangles engineered for Florida’s wind codes. We’ve designed, ordered, and set these windows since 2008, and Dale Kessler’s crew has been setting glass in this part of Palm Beach County since 2008. A window that is not square to the rough opening fails early and fights the framing every hurricane season. Call (561) 708-6771 and we’ll measure the opening twice, spec the shape honestly, and give you a written quote covering the entire job before any work begins.
This is not trim-carpenter work. A hexagonal fixed window on a canal-front home in Golf, a radius top unit over a transom in Manalapan, or a 14-foot wide opening facing the ocean in Ocean Ridge all require engineering calculations, manufacturer coordination, and a set that leaves the pane true. We stand behind that work with both warranty layers registered in writing and our Done Right Promise behind every installation. If the pane is not true, the job is not done.
What Our Custom & Geometric Windows Service Includes
Custom window work in Boynton Beach breaks into four categories, and we handle each one differently because the structural requirements are different. Here is what each involves and when you need it.
Custom Impact Windows
Custom impact windows are code-rated laminated glass units built to a specific opening size and shape, tested to withstand wind-borne debris at the design pressures for Palm Beach County. You need this when a standard catalog window will not fit the rough opening, or when you want a specific shape without sacrificing the hurricane protection your insurance carrier and the Florida Building Code require. We order from PGT and CGI lines when the shape demands custom production, and we register both the glass warranty and the frame warranty in writing before our truck leaves your driveway.
Geometric & Shaped Windows
Geometric and shaped windows are non-rectangular fixed units: octagons, pentagons, triangles, half-rounds, quarter-rounds, and clipped-corner designs that give a home its curb identity. In Boynton Beach, these units commonly fail at the seal or show stress cracks at the corners, because a polygon puts concentrated force at each vertex. TruePane measures every angle to the degree, orders the insulated unit with the correct spacer system for our humidity, and sets the window so the load is carried by the frame, not the glass.
Arched & Curved Windows
Arched and curved windows include eyebrow tops, full-radius units, ellipse windows, and Palladian assemblies found on many 1980s and 1990s Boynton Beach homes. They are the most demanding shapes to order: templet measurements must be exact because the radius has to match the rough opening or the reveal looks wrong and the seal fails prematurely. We take physical templates on site, not from the homeowner’s sketch, and we coordinate directly with the manufacturer’s engineering department so the unit arrives as drawn. When we set an arch, we check the reveal with a radius gauge, not by eye.
Oversized Openings
Oversized openings are window spans wider than about 8 feet or taller than 6 feet, common on new coastal construction and remodeled great rooms from Lantana to Gulf Stream. The engineering question is not the glass alone; it’s the header above, the anchoring around the perimeter, and the deflection limits under wind load. TruePane pulls the panel specs, verifies the rough opening with a laser, and works with your builder or your own structural engineer when the header needs attention. Most of these jobs are completed in a single visit once the unit arrives from the manufacturer.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Custom & Geometric Windows
We use PGT for most of our custom impact-shaped work in Boynton Beach. PGT’s WinGuard line carries the Miami-Dade NOA that Florida inspectors recognize on custom-radius and multi-angle units. We know their lead times, their lamination options, and their spacer systems well enough to quote accurately the first time. When a homeowner wants a clear view with lower profile frames on a geometric fixed window, we often quote CGI’s Estate Collection side by side with PGT so the difference in frame width, glass tint, and price is visible on paper before any order goes in.
For non-impact custom shapes and specialty glazing where the opening is protected by a porch or where local code does not require impact glass, we work with other domestic fabricators that handle true divided lites and arched sash work. If you have an existing PGT or CGI unit that has failed, we can usually source the replacement insulated glass unit directly rather than replacing the entire frame. Whether you have PGT, CGI, Therma-Tru, or any other make, we can measure, quote, and install the correct replacement.
Signs You Need Custom & Geometric Windows Right Now
- Stress cracks at the corners of a fixed shape. A diagonal crack running from the vertex of an octagon or triangle is not cosmetic; the glass was likely glazed too tight or the rough opening is out of tolerance. The lamination or tempering is compromised, and in an impact-rated unit, that rating is gone. We replace the unit, not just the sash.
- Fog between the panes of an insulated arch or half-round. Condensation you cannot wipe away means the seal is dead and the inert gas is gone. The unit is no longer insulating, and replacement is the only fix. We match the original radius and glass package exactly.
- A fixed pane you can deflect by hand. When you push on a large trapezoid or triangle window and the glass moves, the framing is under-engineered or has pulled loose from the rough opening. On a coastal home in Ocean Ridge or Manalapan, that condition fails quickly under wind load.
- Rotted or soft framing around any curved or shaped unit. Boynton Beach’s humidity and salt air eventually get behind any seal that was marginal from the start. A soft jamb in a geometric opening in a Golf home means the window is no longer anchored to structure. We address the opening, not just the glass.
- Water staining below an eyebrow or arch window. Rainwater follows the curve and migrates in at the apex if the flashing was done with flat-window techniques. Staining below a curved top is a flashing failure. We cut it out, re-flash for the actual radius, and reset the unit so water sheds outward.
Our Custom & Geometric Windows Process - Step by Step
- 1
Site measurement and opening inspection. We measure the rough opening at multiple points with a laser and inspect the header, jambs, and sill for deflection-free anchoring. A physical template is taken for any radius or multi-angle shape because a tape measure will not capture a true ellipse.
- 2
Written quote with side-by-side manufacturer options. You get a written, line-item quote that shows the glass system, frame material, finish, impact rating if required, and lead time. Where two manufacturers make a comparable unit, we quote both on paper so the choice is clear.
- 3
Engineering and permit coordination. For impact units and oversized openings, we pull the product approvals and, where your city requires it, the permit. We handle the paperwork and schedule the inspection after install so you do not chase the building department.
- 4
Installation by our own uniformed technicians. The unit is set true to the opening with the reveal checked all the way around, anchored to the manufacturer’s schedule, and flashed to shed water. We are not subcontracting your custom window to the lowest bidder; the same crew that measured it installs it.
- 5
Warranty registration and final walkthrough. Before the truck leaves your driveway, both warranty layers are registered in writing and you get the durations stated on your paperwork. You walk the job with the lead tech, check the reveal, and we answer any question on the spot. That is the Done Right Promise at work.
How Much Does Custom & Geometric Windows Cost in Boynton Beach?
A custom geometric window in Boynton Beach runs $900 to $3,200 per opening depending on size, shape complexity, glass package, and impact rating. A radius-top fixed transom under 4 feet wide usually lands between $900 and $1,600 for non-impact and $1,400 to $2,600 for impact-rated. Full ellipticals and oversized arched units over 6 feet wide typically cost $2,200 to $4,500. A 14-foot oversize opening engineered for coastal wind loads in Gulf Stream or Ocean Ridge is a different scope and is quoted by the individual job, not per window.
| Window Type | Typical Boynton Beach Price Range |
|---|---|
| Custom fixed shape (non-impact) | $900 - $1,800 |
| Custom impact fixed shape | $1,400 - $3,200 |
| Arched or radius top (non-impact) | $1,100 - $2,400 |
| Arched or radius top (impact) | $1,600 - $3,800 |
| Oversized opening (8+ ft, impact) | $3,000 - $7,500+ |
The price moves with glass type (laminated impact versus tempered insulated), low-E coatings, frame finish, and the rough opening condition. If the framing is soft from years of Boynton Beach humidity, the repair work adds to the bottom line, and we will tell you before we order glass. The free estimate we give includes the measurement, the physical template, the manufacturer options, and the written quote. You will not get a lowball number that changes after we open the wall.
Custom & Geometric Windows Near Boynton Beach - Our Service Area
We serve custom window jobs throughout southern Palm Beach County, including Boynton Beach, South Palm Beach, Golf, Lantana, Manalapan, Ocean Ridge, Gulf Stream, Atlantis, Delray Beach, Lake Worth Beach, Greenacres, and Palm Springs. For most custom and geometric window work, we schedule the site measurement within the week and order the unit the same day the template is taken. A live person answers our phone 24 hours a day, 7 days a week, so a question about your project never waits for a callback. Call (561) 708-6771.
Serving Boynton Beach, FL - Our Local Coverage Area
We’re based in the Boynton Beach area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Custom & Geometric Windows in Boynton Beach
A custom geometric window is a fixed or operable glass unit built to a non-standard shape and size: a triangle, trapezoid, octagon, circle, half-round, or other multi-angle form. When you need one of these for a Boynton Beach home, it is ordered to exact measurements taken on site, not pulled from a catalog rack. TruePane has templated and installed these shapes since 2008, and Dale Kessler’s glazing work spans more than years in Palm Beach County. Call (561) 708-6771 for a free measurement and quote.
A standard custom fixed shape takes about 3 to 6 weeks from template to installation, depending on the manufacturer’s lead time and the glass package. Impact-rated units and laminated arches run 5 to 10 weeks because they are built to order and tested to the product approval. Our installation visit for most single openings takes one day once the unit arrives. We give you a written lead time with your quote so you know when the crew arrives before we order the glass.
A custom non-impact geometric window typically runs $900 to $1,800, an impact-rated unit $1,400 to $3,200, and oversized openings $3,000 to $7,500 plus. The price depends on the size, shape complexity, glass type, coating, and the condition of the rough opening. Your written quote shows every line item, and the price is fixed unless we find a structural problem you have approved repairing. Call (561) 708-6771 for your free estimate.
Yes, we install and replace custom PGT and CGI windows, including the impact-rated WinGuard and Estate Collection lines. We have worked with both manufacturers’ product approvals, NOA numbers, and warranty registration processes on jobs across Boynton Beach, Golf, and the coastal communities. We source the correct insulated glass unit and set the replacement to the original reveal. A written quote covers both manufacturers side by side when either would do the job.
For a broken impact window or a unit that is open to weather in Boynton Beach, we get a technician to the home quickly to secure the opening and measure for the replacement. A live person answers our phone 24 hours a day, 7 days a week, not a call center and not a voicemail tree. The replacement glass usually has to be manufactured to the template, so the opening gets boarded or covered safely until the new unit arrives. Call (561) 708-6771 and ask to speak with a technician.
Every custom window carries both warranty layers registered in writing before the truck leaves the driveway: the manufacturer’s coverage on glass and frame, stated with its duration, and our workmanship on the installation. You get no fine print that covers neither. If anything is not done right on the install, our Done Right Promise means we make it right with no paperwork fight. We stand behind it.
Clear the area inside and outside the window about 6 feet back from the opening, remove window coverings, and move furniture and wall art out of the work zone. On the day of install, our technicians protect the floors and the surrounding walls with drop cloths and masking. Most custom replacements in Boynton Beach are a single-day visit once the unit is on our truck. We will walk you through the prep on the phone when you schedule.
Schedule Your Custom & Geometric Windows Service in Boynton Beach Today
You have lived with that opening long enough. Call (561) 708-6771 and a person answers the phone, 24/7. We will schedule the measurement, write the quote, and give you a square deal on a custom window that fits the opening and stands up to Boynton Beach weather. The estimate is free and there is no obligation. We’ll be there when we say.
Written by Dale Kessler, Owner at TruePane Windows & Doors, serving Boynton Beach since 2008.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.