Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterECO Window Systems Custom & Geometric Windows in Boynton Beach: What to Know First
We install, repair, and replace ECO Window Systems custom and geometric windows throughout Boynton Beach, and most jobs are completed in a single visit. A typical custom-shaped ECO unit, arched or radius, runs $900 to $3,800 depending on size, glass package, and framing condition. We are an independent ECO Window Systems service provider, not a factory branch, which means we quote honestly and fix what is actually wrong. If you own an ECO window that has lost its seal, binds in the frame, or never fit right from the day it was installed, call (561) 708-6771 and we will send a technician who has worked on these units before.
How ECO Window Systems Products Fail - and How We Fix Them
ECO Window Systems builds a solid product, but custom and geometric shapes put stress on components that standard rectangles never see. Here are the failures we actually find in Boynton Beach homes:
- Radius and arch units losing argon at the curved seal. The Thermo-Vinyl and impact-arch lines have a bent-glass stress point where the curve meets the straight leg. In Boynton Beach, the summer heat and humidity cycles pull that seal apart, and the glass fogs in July, never in March. We replace the insulated glass unit using the original opening measurements, not the old glass, because a curved frame settles over time.
- Geometric window frames racking after storm-driven wind load. Triangle, trapezoid, and pentagon units take lateral pressure differently than rectangular frames. After a strong season of Boynton Beach thunderstorms, the corners can open up just enough to let air and water through. We re-square the rough opening, shim the frame properly, and re-set the unit instead of just caulking over the gap.
- Hardware fatigue on casement-style geometric windows. ECO’s manual casement and awning operators on non-rectangular frames wear faster because the hinge geometry is working against the glass weight at an angle. Owners often assume the crank is broken when actually the friction hinge has spread. We replace the hinge and reset the sash travel so the window closes square again.
- Poorly supported oversized openings from original installs. We have removed oversized fixed geometric units in Hunters Run and Chapel Hill where the original installer used undersized jamb extensions and called it good. The glass sagged, the reveal opened, and the frame bowed. We re-hang the unit with proper load transfer to the header and re-trim it so the wall carries the weight, not the window.
- Weep holes blocked or missing on custom sill profiles. Some ECO custom-shaped windows with contoured sills arrive without sufficient drainage, and Boynton Beach rain finds the entry. We drill and fit the sill with proper weeping details so water exits the track instead of pooling and wicking into the frame.
Our ECO Window Systems Custom & Geometric Windows Process
When you call TruePane Windows & Doors about an ECO custom or geometric window, you get a process that has not changed much in the four decades Dale Kessler has been setting glass in Palm Beach County.
- 1
We measure, then measure again. Every opening gets measured twice: once at the rough framing, once at the finished opening. Custom and geometric windows do not forgive a sloppy number.
- 2
We show you the parts decision on paper. For ECO units, we lay out OEM versus quality aftermarket options in writing: cost, lead time, and warranty range. You choose, we document it. If it is not in writing, it is not a guarantee, it is a conversation.
- 3
We order or fabricate the piece to the opening, not to the old part. A curved frame shifts over time. Cutting new to the old dimensions just repeats the failure.
- 4
We set, shim, and seal the unit true. Level, plumb, square, and properly supported at every point where the frame meets the rough opening. That is The Keystone Standard.
- 5
We test the unit in front of you. We operate the sash, check drainage, run water on the sill, and inspect the reveal gaps. You see the window function before we pack up.
- 6
We register the warranty and leave the paperwork on your counter. Both manufacturer warranty layers, durations stated, and our Done Right Promise in writing before the truck leaves the driveway.
What ECO Window Systems Custom & Geometric Windows Costs in Boynton Beach
We price by the opening, the glass package, and the condition of the existing frame. Here are honest ranges for the ECO work we most often do in Boynton Beach:
- Arched fixed glass replacement, insulated: $900 to $2,400 installed
- Triangle or trapezoid fixed unit, single opening: $1,100 to $2,800 installed
- Curved or true radius window, custom bent glass: $1,800 to $3,800 installed
- Oversized geometric replacement with reinforced framing: $2,500 to $5,500 installed
- Full custom-wall geometric window system: $6,000 to $14,000 installed
What moves the price is the glass: impact-rated, low-E, laminated, or tinted all cost different. Framing condition matters too. If the rough opening is out of square, we correct it before the new unit goes in, and that labor appears as its own line item on the quote. We do not bury it. Call (561) 708-6771 and we will give you a written, line-by-line estimate for your specific window.
Why Boynton Beach Homeowners Call TruePane Windows & Doors for ECO Window Systems Work
We have been doing glass and windows in this community since 2008. Dale Kessler grew up off Lawrence Road in the Meadows section of Boynton Beach, and he still treats every job like his mother is going to stand at the window and check the reveal. Our technicians are background-checked, uniformed, and trained on more than a dozen manufacturer lines, including PGT, CGI, CWS, and ES Windows, so if your ECO window is beyond saving, we quote you real alternatives side by side on paper. We register both warranty layers before we leave the driveway. And our Done Right Promise is not a voucher for more paperwork. If something is not right, we come back and make it right.
FAQs
Yes. We measure the rough opening and template the existing frame, then order a replacement unit cut to the same radius, angle, or curve. The original unit’s paper label rarely tells the full story, so we measure from the wall, not the old glass. Call (561) 708-6771 and we will confirm what is matchable in your specific window.
If the window is still under ECO’s original warranty, we work with you to file a claim through the proper channel and use OEM parts where the coverage requires it. As an independent ECO Window Systems service provider, we do not make warranty decisions for the manufacturer, but we document the failure in the language the warranty department understands. If the warranty has lapsed, we quote OEM and aftermarket options side by side and let you decide.
The three deciding factors are seal failure, frame integrity, and glass damage. If the frame is racked, the sash binds, or the corner welds have opened, replacement is generally the honest call. If the frame is square and the only problem is fogged glass or a failed hinge, repair costs less. We will put the choice in writing with prices for both before you spend a dollar.
Most standard custom shapes are installed in one day once the unit arrives. Lead time for the glass runs two to four weeks depending on the shape and whether the opening requires impact-rated or laminated glass. We confirm the timeline in writing at the estimate, and we show up on the day we name.
Yes. When a permit is required, we pull it, schedule the inspection, and stand behind the result. We have done enough jobs in Boynton Beach to know which replacements sail through and which ones need a structural note from an engineer. You will never hear us tell you to handle the permit yourself to save a few dollars.
If your ECO Window Systems custom or geometric window needs attention, call (561) 708-6771. We will schedule a free estimate and give you a written quote with no surprises.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Boynton Beach and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.