Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterCWS Roof Repair in Boynton Beach: What to Know First
We repair CWS roof systems in Boynton Beach as an independent service provider, not a CWS dealer. Most CWS roof repairs in this area run between $450 and $2,800 depending on what failed and whether we can save the existing curb or flashing. We typically complete CWS roof work in one visit because we stock the common failure parts and know which aftermarket components hold up in South Florida humidity.
This page is for homeowners in Boynton Beach who own a CWS roof and need straight answers about what failed, what it costs to fix, and whether the repair will hold. If you’re looking at a leak, a lifted flashing, or a failed seam, call us at (561) 708-6771 and we’ll walk through the symptoms before we ever send a truck.
How CWS Products Fail - and How We Fix Them
- Lifted lap seams on the CWS standing seam profile. In Boynton Beach, the combination of afternoon sea breeze and intense UV cycles causes the seams on older CWS standing seam panels to flex and eventually separate at the lap points. Water gets under the seam edge and travels toward the fasteners. We see this on the CWS Tuff-Rib and comparable profiles. The fix is reseating the seam, replacing any corroded clips, and sealing with a polyether sealant that handles the thermal movement.
- Failed pipe boot gaskets around roof penetrations. CWS installs standard EPDM pipe boots on most residential jobs, and EPDM cracks in the South Florida sun faster than silicone or thermoplastic alternatives. By the time a homeowner notices the brown stain on the ceiling, the gasket has usually been split for months. We replace cracked boots with a silicone-based option and inspect the surrounding panel for rust before sealing.
- Rust-through at the eave line where CWS panels meet the gutter. This is the one most homeowners miss. CWS panels drain toward the eave, and if the gutter install left the panel edge touching standing water, electrolysis starts eating the metal from the underside. You’ll see pin-prick rust spots on the underside of the eave panel. We cut out the compromised section and install a replacement panel matched to the existing profile, then correct the gutter slope so water doesn’t pool there again.
- Loose or missing fasteners on CWS ridge caps. The ridge cap takes the full force of every storm that crosses Boynton Beach, and the original fasteners on older CWS installs eventually back out from repeated thermal expansion. A loose ridge cap makes a rattling sound in a good wind and lets water in during heavy downpours. We resecure the cap with new stainless fasteners, replace the neoprene washers, and check the underlying Z-flashing for cracks.
- Failed sealant at CWS skylight and vent transitions. CWS curbs for skylights and attic vents are built onsite, and the original sealant bead between the curb and the panel is the first thing to go in a coastal salt environment. In the communities west of I-95 around Boynton Beach, we see this after about 8 to 10 years. We remove the old bead completely, clean the joint, and reapply a marine-grade sealant that bonds to both the painted panel and the curb flange.
Our CWS Roof Repair Process
- 1
You call, a person answers. No automated menu. You’ll tell us the symptoms: where the drip shows up, when you first noticed it, and whether it gets worse in a downpour. We’ll give you a working theory before we schedule the visit.
- 2
We inspect the roof and the attic. On site, the technician looks at the CWS panels from above and the decking from below. Water travels, so the stain inside rarely matches the hole outside. We trace the path, not the puddle.
- 3
We make a parts decision with you. If the original CWS panel is still available, we price it. If the line has been discontinued or the lead time is absurd, we source a quality aftermarket panel or component that matches the profile and gauge. You’ll see both numbers on paper before any work starts.
- 4
We do the repair. The work is done with the right fasteners for CWS’s gauge and profile, correct sealants for South Florida, and no shortcuts on the lap points. One visit, done right.
- 5
We water-test the repair. A garden hose test on the exact seam or penetration we fixed, not an inspection from the ground. If water gets in, we haven’t left yet.
- 6
Everything is written down. You get the work summary, the parts used, the warranty terms, and our signature on the job. If it’s not in writing, it’s not a guarantee - it’s a conversation.
What CWS Roof Repair Costs in Boynton Beach
Here’s what we charge for the most common CWS roof repairs we see in Boynton Beach:
- Pipe boot replacement: $450-$800
- Seam reseal and fastener replacement (single area): $600-$1,200
- Ridge cap resecure and reseal: $800-$1,500
- Eave panel replacement (rust-through): $1,200-$2,800
- Skylight or vent curb reseal: $700-$1,400
What moves the price: roof pitch, access, whether the CWS profile is still in production, and how far the water traveled. A leak that sat for two seasons is a bigger job than the same leak caught early. Call (561) 708-6771 and we’ll quote the job honestly, on paper, with no surprises when the bill comes.
Why Boynton Beach Homeowners Call TruePane Windows & Doors for CWS Work
We’re not a CWS dealer and we don’t pretend to be. We’re an independent service company that has spent over four decades working on South Florida homes, and we’ve seen enough CWS roofs to know where they fail and what actually fixes them. Dale Kessler grew up off Lawrence Road in the Meadows section of Boynton Beach, so when we say we understand what coastal heat and salt air do to a roof system, it’s not a pitch. It’s the reason we stock the parts we stock.
Every CWS repair we do is backed by the Done Right Promise. If it’s not right, we come back and make it right - no paperwork fight. We also handle PGT, CGI, ES Windows, and ECO Window Systems for homeowners whose roof repair turns into a conversation about the skylights and windows that sit in that roof. One call covers more of the building envelope than most companies will touch. A live person answers whenever you call, day or night.
FAQs
No, not on the surrounding roof system. CWS material warranties cover manufacturing defects in the panels, not installation issues or normal weather-driven wear. An independent repair doesn’t void a materials warranty, but we’ll review your specific warranty documents and flag anything that needs attention before we start work. Call (561) 708-6771 and we’ll walk through what your paperwork actually says.
Usually, yes. If the original CWS panel profile is still in production, we order from CWS’s current color chart. If the line has been discontinued or the color has faded significantly, we’ll show you the closest available match on paper before any metal is cut. The goal is a repair you can’t point to from the street.
Most CWS repairs are finished in a single visit, typically four to six hours on the roof. Pipe boots and seam repairs are faster, eave panel replacement takes longer. We carry the common fasteners, sealants, and profiles on the truck so we don’t leave you with a tarp and a promise for another appointment.
If the damage is confined to one section, a repair is the right call. If the fasteners are failing in multiple areas and the panels show widespread rust, we’ll tell you straight up that a repair buys time, not decades. We’ll give you both numbers and let you decide without pressure.
Yes. CWS skylight curbs and transitions are a regular part of our roof repair work in Boynton Beach. We reseal the curb, check the flashing, and test everything with a hose before we pack up.
If you own a CWS roof in Boynton Beach and it’s leaking, lifting, or making noise in a storm, call (561) 708-6771 for a free estimate. We’ll show up when we say, explain what we found in plain terms, and put the quote in writing.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Boynton Beach and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.